CrazyF4 ELRS flight controller built-in 915MHz expresslrs receiver. CrazyF4 ELRS flight controller built-in 868MHz expresslrs receiver. MCU:STM32F411CEU6 (100MHZ, 512K FLASH). Board size: 28.5 28.5MM. Power supply: 1S battery input (DC 2.9V-4.35V).
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready. Built-in Betaflight OSD(SPI Control). Built-in ExpressLRS 2.4G/915MHz/868MHz receiver. Power supply: 1S LiPo/LiPo HV.Current: 5A continuous peak 6A (3 seconds). Onboard SPI ExpressLRS 2.4GHz Receiver.
Could bind with Happymodel ES24TX, ES24TX Lite, ES24TX Slim and DIY. 2.4GHz ELRS TX module ExpressLRS version 1.0.0 or 1.0.1 both compatible. RF Frequency optional: 915mhz or 868mhz(EU).
Could bind with Happymodel ES915TX, Frsky R9M and DIY ELRS TX module(need to flash the same version ELRS firmware). Firmware flash via Betaflight pass-through.
Input voltage: 3.3V 5.5V. Frequency: 5.8GHz 5bands 40 channels. Lens : 2.1mm(M8) FOV 160°.
Signal System: PAL/NTSC Non Switchable. Auto Gain Control (AGC): Auto.Built-in 1000 mAh 1S battery, LiteRadio 2 SE increases the endurance to 8 hours. Updates with BETAFPV self-developed LiteRadio System. Pilots can directly operate the Joystick Calibration and Upgrade Firmware on the radio transmitter. Supports the Frsky / Futaba / Bayang, pilots can easily change Futaba, Frsky D8, Frsky FCC D16, and Frsky LBT D16 mode via the radio transmitter. Comes with 100mW transmitting power, LiteRadio 2 SE brings a wider operating range. LiteRadio 2 SE upgrades with BETAFPV self-developed Customized LiteRadio System. Pilots can directly operate the Joystick Calibration and Firmware Update on the radio transmitter, which is more convenient for the beginner racer to operate. Equipped with a built-in 1000 mAh 1S battery, LiteRadio 2 SE can use up to 8 hours, bringing an excellent endurance performance. Comes with a built-in charging module, LiteRadio 2 SE can support USB charging which is more convenient to use. Meanwhile, it designs a Low-Power warning to indicate a low battery.
While it needs to be re-charged(when the voltage is lower than 3.5V), the LED will turn red first, then it will turn blue and flash slowly. LiteRadio 2 SE has a larger transmitting power that can reach 100mW, bringing a wider operating range.
Adopted the rubber coat, LiteRadio 2 SE is ergonomic and has the shape of a gaming controller. It's comfortable to hold, and the anti-slip texture on the handles allows for a solid grip. This radio transmitter acts as a USB Joystick when connected to a personal computer. So you could use it to play FPV simulators like EREADRONE.LiteRadio 2 SE transmitter has been equipped on the Ready-to-Fly FPV whoop racing advanced kit 2 and FPV whoop racing starter kit 2. It is one of the easiest ways to get into the FPV hobby.
Frequency Range: 2.4G (2403MHz-2447MHz). 2.4G System: NRF24L01 / CC2500 / SX1280. Support Protocol: Bayang / Futaba S-FHSS / Frsky FCC D16/ Frsky LBT D16 / Frsky D8 / ExpressLRS 2.4G. Support USB Charging / Firmware Update. Support BETAFPV Simulator Connected / Customized LiteRadio System / Joystick Calibration.
LED Light: Green-Power On / Red-Warning if the voltage is lower than 3.5V / Blue-Normal. Battery: Built-in 1000mAh 1S Battery. Charging Connector: USB 3.0 Type-C. BETAFPV Configurator is utility designed to simplify updating, configuring and tuning the radio transmitter. Function of BETAFPV Configurator is list below.
Basic radio controller setup, like mode switch, turn on/off RF modules. Full function of the ExpressLRS configuration, like outpower, packet rate etc.
Channel mixer for fix wing drones. How to recognise if your radio transmitter supports the BETAFPV Configurator? Remove the cover on the back of the transmitter and there is a label, comes with "BETAFPV Configurator Supported".
How to switch the protocol. This item is in the category "Toys & Hobbies\Radio Control & Control Line\RC Model Vehicle Parts & Accs\Other RC Parts & Accs". The seller is "miaozhengtc" and is located in this country: CN. This item can be shipped worldwide.